雷竞技电竞
服务号
当前位置: 首页? 专业英语? 专业词汇? 正文

焊接专业英语词汇(3)

放大字体缩小字体发布日期:2008-04-07
核心提示:焊接热循环 weld thermal cycle 焊接温度场 field of weld temperature; weld temperature field 准稳定温度场 quasi-stationary temperature field 焊接热源 welding heat source 点热源 point heat source 线热源 linear heat source 面热源 plane heat source 瞬时

      焊接热循环 weld thermal cycle
      焊接温度场 field of weld temperature; weld temperature field
      准稳定温度场 quasi-stationary temperature field
      焊接热源 welding heat source
      点热源 point heat source
      线热源 linear heat source
      面热源 plane heat source
      瞬时集中热源 instantaneous concentration heat source
      热效率 thermal efficiency
      热能集中系数 coefficient of heat flow concentration
      峰值温度 peak temperature
      瞬时冷却速度 momentary cooling rate
      冷却时间 cooling time
      置换氧化 substitutionary oxydation
      扩散氧化 diffusible oxydation
      脱氧 desoxydation
      先期脱氧 precedent desoxydation
      扩散脱氧 diffusible desoxydation
      沉淀脱氧 precipitation desoxydation
      扩散氢 diffusible hydrogen
      初始扩散氢 initial diffusible hydrogen
      100℃残余扩散氢 diffusible hydrogen remained at 100℃
      残余氢 residual hydrogen
      去氢 dehydrogenation
      去氢热处理 heat treatment for dehydrogenation
      脱硫 desulphurization
      脱磷 dephosphorization
      渗合金 alloying
      微量合金化 microalloying
      一次结晶组织 primary solidification structure
      二次结晶组织 secondary solidification structure
      联生结晶 epitaxial solidification
      焊缝结晶形态 solidification mode in weld-bead
      结晶层状线 ripple
      多边化边界 polygonization boundary
      结晶平均线速度 mean solidification rate
      针状铁素体 acicular ferrite
      条状铁素体 lath ferrite
      侧板条铁素体 ferrite side-plate
      晶界欣素体 grain boundary ferrite; polygonal ferrite; pro-entectoid ferrite
      粒状贝氏体 granular bainite
      板条马氏体 lath martensite
      过热组织 overheated structure
      魏氏组织 Widmannst?tten structure
      M-A组元 martensite-austenite constituent
      焊件失效分析 failure analysis of weldments
      冷裂判据 criterion of cold cracking
      冷裂敏感系数 cold cracking susceptibity coefficient
      脆性温度区间 brittle temperature range
      氢脆 hydrogen embrittlement
      层状偏析 lamellar segregation
      愈合 healing effect
      断口金相fractography
      断口 fracture
      延性断口 ductile fracture
      韧窝断口dimple fracture
      脆性断口 brittle fracture
      解理断口 cleavage fracture
      准解理断口 quasi-cleavage fracture
      氢致准解理断口 hydrogen-embrittlement induced
      沿晶断口 intergranular fracture
      穿晶断口 transgranular fracture
      疲劳断口 fatigue fracture
      滑移面断口 glide plane fracture
      断口形貌 fracture apperance
      断口试验 fracture test
      宏观断口分析 macrofractography
      放射区 radical zone
      纤维区 fibrous zone
      剪切唇区 shear lip aone
      焊接性weldability
      使用焊接性 service weldability
      工艺焊接性 fabrication weldability
      冶金焊接性 metallurgical weldability
      热焊接性 thermal weldability
      母材 base metal; parent metal
      焊接区 weld zone
      焊态 as-welded (AW)
      母材熔化区 fusion zone
      半熔化区 partial melting region
      未混合区 unmixed zone
      熔合区 bond area
      熔合线 weld junction (英);bond line (美)
      热影响区 heat-affected zone (HAZ)
      过热区 overheated zone
      粗晶区 coarse grained region
      细晶区 fine grained region
      过渡区 transition zone
      硬化区 hardened zone
      碳当量 carbon equivalent
      铬当量 chromium equivalent
      镍当量 nickel equivalent
      舍夫勒组织图 Schaeffler's diagram
      德龙组织图 Delong’s diagram
      连续冷却转变图(CCT图)continuous cooling transformation
      裂纹敏感性 cracking sensibility
      焊接裂纹 weld crack
      焊缝裂纹 weld metal crack
      焊道裂纹 bead crack
      弧坑裂纹crater crack
      热影响区裂纹 heat-affected zone crack
      纵向裂纹 longitudinal crack
      横向裂纹 transverse crack
      微裂纹 micro-crack; micro-fissure
      热裂纹 hot crack
      凝固裂纹 solidification crack
      晶间裂纹 intercrystalline crack
      穿晶裂纹 transcrystalline crack
      多边化裂纹 polygonization crack
      液化裂纹 liquation crack
      失延裂纹 ductility-dip crack
      冷裂纹 cold crack
      延迟裂纹 delayed crack
      氢致裂纹 hydrogen-induced crack
      焊道下裂纹 underbead crack
      焊根裂纹 root crack
      焊趾裂纹 toe crack
      锯齿形裂纹 chevron cracking
      消除应力处理裂纹 stress relief annealing crack (SR crack)
      再热裂纹 reheat crack
      焊缝晶间腐蚀 weld intercryctalline corrosion
      刀状腐蚀 knife line attack
      敏化区腐蚀 weld decay
      层状撕裂 lamellar tearing
      焊接性试验 weldability
      裂纹试验 cracking test
      IIW裂纹试验 IIW cracking test
      Y形坡口裂纹试验 slit type cracking test
      分块形槽热裂纹试验 segmented circular groove cracking test
      H形裂纹试验 H-type cracking test
      鱼骨形裂纹试验 fishbone cracking test
      指形裂纹试验 finger (cracking) test
      T形裂纹试验 Tee type cracking test
      环形槽裂纹试验 circular-groove cracking test
      可调拘束裂纹试验 varestraint test
      BWRA奥氏体钢裂纹试验 BWRA cracking test for austenitie steel
      圆棒裂纹试验 bar type cracking test; round bar cracking test
      里海裂纹试验 Lehigh restraint cracking test
      圆形镶块裂纹试验 circular-path cracking test
      十字接头裂纹试验 cruciform cracking test
      Z向窗口拘束裂纹试验 Z-direction window type restraint cracking test
      G-BOP焊缝金属裂纹试验 G-BOP weld metal crack test
      巴特尔焊道下裂纹试验 Battelle type underbead cracking test
      U形拉伸试验 U-tension test
      缪雷克期热裂纹试验 Murex hot cracking test
      菲斯柯裂纹试验 FISCO (type) cracking test
      CTS裂纹试验 controlled thermal severity
      拉伸拘束裂纹试验(TRC试验)tensile restraint cracking test
      刚性拘束裂纹试验(RRC试验)rigid restraint cracking test
      插销试验 implant test
      Tigamajig 薄板焊接裂纹试验 Tigamajing thin plate cracking test
      焊道纵向弯曲试验 longitudinal-bead test
      柯麦雷尔弯曲试验 Kommerell bead bend test
      肯泽尔弯曲试验 Kinzel test
      缺口弯曲试验 notch bend test
      热朔性试验 hot-ductility test
      热影响区冲击试验 impact test of HAZ
      热影响区模拟试验 synthetic heat-affected zone test
      最高硬度试验 maximum hardness test
      落锤试验 NRL (Naval Research Laboratory)
      测氢试验 Hydrogen test
      焊接材料
      电极
      焊接材料welding consumables
      电极electrode
      熔化电极consumable electrode
      不熔化电极nonconsumable electrode
      钨电极tungsten electrode
      焊丝welding wire. Welding rod
      实心焊丝solid wire
      渡铜焊丝copper-plating welding wire
      自保护焊丝self-shielded welding wire
      药芯焊丝flux-cored wire
      复合焊丝combined wire
      堆焊焊丝surfacing welding rod
      填充焊丝filler wire
      焊条electrode/ covered electrode
      焊芯core wire
      药皮coating (of an electrode)/ covering (of an electrode)
      涂料coating flux/coating material
      造气剂gas forming constituents
      造渣剂slag forming constituents
      合金剂alloying constituent
      脱氧剂dioxidizer
      稳弧剂arc stabilizer
      粘接剂binder
      水玻璃water glass
      水玻璃模数modules of water glass
      酸性焊条acid electrode
      高钛型焊条high titania (type) electrode
      钛钙型焊条lime titania type electrode
      钛铁矿形焊条ilmenite type electrode
      氧化铁型焊条iron oxide type electrode/ high iron oxide type electrode
      高纤维素型焊条high cellulose (type) electrode
      石墨型焊条graphite type electrode
      碱性焊条basic electrode/ lime type covered electrode
      低氢型焊条low hydrogen type electrode
      高韧性超低氢焊条high toughness super low hydrogen electrode
      奥氏体焊条austenitic electrode
      铁素体焊条ferritic electrode
      不锈钢焊条stainless steel electrode
      珠光体耐热钢焊条pearlitic heat resistant steel electrode
      低温钢焊条low temperature steel electrode/ steel electrode for low temperature
      铝合金焊条aluminum alloy arc welding electrode
      铜合金焊条copper-alloy arc welding electrode
      铜芯铸铁焊条cast iron electrode with steel core
      纯镍铸铁焊条pure nickel cast iron electrode
      球墨铸铁焊条electrode for welding spheroidal graphite cast iron
      铸芯焊条electrode with cast core wire
      镍基合金焊条nickel base alloy covered electrode
      蒙乃尔焊条Monel electrode
      纯铁焊条pure iron electrode
      渗铝钢焊条alumetized steel electrode
      高效率焊条high efficiency electrode
      铁粉焊条iron powder electrode
      底层焊条backing welding electrode
      深熔焊条deep penetration electrode
      重力焊条gravity electrode
      立向下焊条electrode for vertical down position welding
      节能焊条saving energy electrode
      水下焊条underwater welding electrode
      耐海水腐蚀焊条seawater corrosion resistant steel electrode
      低尘低毒焊条low-fume and harmfulless electrode/
      low-fume and low-toxic electrode
      堆焊焊条surfacing electrode
      耐磨堆焊焊条hardfacing electrode
      钴基合金堆焊焊条cobalt base alloy surfacing electrode
      碳化钨堆焊焊条tungsten carbide surfacing electrode
      高锰钢堆焊焊条high manganese steel surfacing electrode
      双芯焊条twin electrode
      绞合焊条stranded electrode
      编织焊条braided electrode
      双层药皮焊条double coated electrode
      管状焊条flux-cored electrode
      气渣联合保护型药皮semi-volatile covering
      焊条工艺性usability of the electrode/ technicality of the electrode
      焊条使用性running characteristics of an electrode/ operating characteristics of an electrode
      焊条熔化性melting characteristics of an electrode
      焊条直径core diameter
      焊条偏心度eccentricity (of an electrode)
      药皮重量系数gravity coefficient of coating
      焊条药皮含水量percentage of moisture for covering
      焊条夹吃持端bare terminal (of an electrode)
      焊条引弧端striking end (of an elcetrode)
      焊剂welding flux/ flux
      熔炼焊剂fused flux
      粘结焊剂bonded flux
      烧结焊剂sintered flux/ agglomerated flux
      窄间隙埋弧焊焊剂flux for narrow-gap submerged arc welding
      低氢型焊剂low hydrogen type flux
      高速焊剂high speed welding flux
      无氧焊剂oxygen-free flux
      低毒焊剂low poison flux
      磁性焊剂magnetic flux
      电弧焊 arc welding
      直流电弧焊 direct current arc welding
      交流电弧焊 alternating current arc welding
      三相电弧焊 three phase arc welding
      熔化电弧焊 arc welding with consumable
      金属极电弧焊 metal arc welding
      不熔化极电弧焊 arc welding with nonconsumable
      碳弧焊 carbon arc welding
      明弧焊 open arc welding
      焊条电弧焊 shielded metal arc welding (SMAW)
      重力焊gravity welding
      躺焊 fire cracker welding
      电弧堆焊 arc surfacing
      自动堆焊 automatic surfacing
      躺板极堆焊 surfacing by fire cracker welding
      带极堆焊 surfacing with band-electrode
      振动电弧堆焊 vibratory arc surfacing
      耐磨堆焊 hardfacing
      埋弧焊 submerged arc welding (SAW)
      多丝埋弧焊multiple wire submerged arc welding
      纵列多丝埋弧焊 Tandem sequence (submerged-arc welding)
      横列多丝埋弧焊 series submerged arc welding (SAW-S)
      横列双丝并联埋弧焊 transverse submerged arc welding
      热丝埋弧焊 hot wire submerged-arc welding
      窄间隙埋弧焊 narrow-gap submerged arc welding
      弧压反馈电弧焊 arc voltage feedback controlling arc welding
      自调节电弧焊 self-adjusting arc welding
      适应控制焊接 adaptive control welding
      焊剂层 burden; flux layer
      气体保护电弧焊 gas shielded arc welding
      保护气体 protective atmosphere
      惰性气体 inert-gas
      活性气体 active-gas
      惰性气体保护焊 inert-gas (arc) welding
      氩弧焊 argon arc welding
      熔化极惰性气体保护电弧焊 metal inert-gas arc welding
      钨极惰性气体保护电弧焊 tungsten inert-gas arc welding
      钨极氢弧焊 argon tungsten arc welding
      脉冲氢弧焊 pulsed argon arc welding
      熔化极脉冲氢弧焊 argon metal pulsed arc welding
      钨极脉冲氢弧焊 argon tungsten pulsed arc welding
      热丝MIG焊 hot wire MIG welding
      热丝TIG焊 hot wire TIG welding
      氨弧焊 helium-arc welding
      活性气体保护电弧焊 metal active-gas arc welding
      混合气体保护电弧焊 mixed gas arc welding
      更多翻译详细信息请点击: http://www.trans1.cn
      关键词: 焊接 词汇
      分享:


      推荐图文
      推荐专业英语
      点击排行
      Processed in 0.117 second(s), 14 queries, Memory 0.92 M
      Baidu
      map